Recent content by gr33nz

  1. G

    Leaves 'rusting', nute burn?

    this might be a problem with your roots check them and if brown and wimpy get some h202 add 8 ml per gal
  2. G

    4 day bud dryer for $40.

    I don't post too often but been reading this great thread, and thought of if it at pets mart when I saw this. It's a bit pricey for a DIY box but could be a great regulated heat source. Ceramic Infrared Heat Emitters Zoo-MedStarting at: $19.99 Ceramic heating devices are much more...
  3. G

    White Widow - Day 57 Flowering

    Re-read the quote!!! This says give it an extended dark perk period saying reduce to 8 on 16 off, or no light just before harvest. Some people do 24-72 hour dark period just prior to harvest to bring out the trichs. YOU ARE RE-VEGGING with 18-6! :sad: Hopefully no issues just switch back to...
  4. G

    White Widow - Day 57 Flowering

    Re-read the quote!!! This says give it an extended dark perk period saying reduce to 8 on 16 off, or no light just before harvest. Some people do 24-72 hour dar period just prior to harvest to bring out the trcihs. YOU ARE RE-VEGGING with 18-6! :sad: Hopefully no issues just switch back to...
  5. G

    when do fanleaves turn yellow in flowering

    plant problem thread with great info! https://www.rollitup.org/general-marijuana-growing/1469-marijuana-plant-problems-cures.html Cheers
  6. G

    when do fanleaves turn yellow in flowering

    Try and keep the PH @ 5.5 to 6.5, ideally around 5.5-6.0. Your Ph is to high. :leaf: http://www.gardenersnet.com/atoz/ph.htm https://www.rollitup.org/view.php?pg=faq&cmd=category&id=51 What pH level or range should I aim for? What pH level or range should I aim for? Marijuana thrives in...
  7. G

    when do fanleaves turn yellow in flowering

    With dead leaves overnight or spots on the leaves it sounds like a serious PH issues or nute burn. Nute def is most likely not the cause. See the following link. https://www.rollitup.org/view.php?pg=faq&cmd=article&id=588 More info normally needed. eg.. ph, type of nutes, min-max temps, RH...
  8. G

    co2 burner run time??

    Buy a Telair 8001 monitor and make your own controller. DIY Wiring for Telaire Co2 Monitor - The Garden's Cure Hopefully it's cool to post the link!! :weed:
  9. G

    Cloning in flowering stage possible?

    Here's a few pics.
  10. G

    Cloning in flowering stage possible?

    It's ok to take clones early in to flower. Normally the first 2-3 weeeks at the latest. Take them from the bottom of the plant. They should grow roots in the normal time. Try using the DIY bubbleponic cloner in the DIY section of the FAQ. There's a 20 inch tupperware container that a propagation...
  11. G

    DWC for beginners

    The general hydro dual diaphram air pump is worth the money around $60 but you can also buy replacement parts to rebuild it. Seen it used for 20G res and 2 5G D/W buckets with 2 round airstones and 2 18 inch air curtains with plenty of bubbles. Comes stock with the GH 6 site setup. Not any...
  12. G

    HeY Check ThiS ouT!!!!.....HelP!?

    Looks like bugs spidermites are pretty small dude you checking under the leafs that's all I could think of tiny small micro specs same shit happen to me didn't know then I got some spitacide
Top