windwalker
Active Member
Good evening ladies and gentlemen.
I'm attempting to copy Scrub's cabinet to use for flowering, with directions found here: https://www.rollitup.org/view.php?pg=faq&cmd=article&id=563 (along with handy dandy pictures) and am having a bit of trouble understanding the directions for building the cabinet. I really like the modular design though, and understand that there are two modules, one sitting above the main chamber and providing ventilation/power management and one sitting below the main chamber providing passive intake.
Later in the guide a carbon filter is added, although I don't quite understand how the top chamber is reworked.
I understand that there are:
3" diam black piping used for creating the light traps
6 ea 3/4" panels of plywood at 84" x 48"
a fan
ducting
bolts and screws
and hinges
and this seems simple enough, the six plywood sheets are cut up into the proper lengths to construct 3 boxes, but I don't quite see how they fit together.
what I don't understand is what the
8 ea 1x2 8' long
and 4 linear ft 1" x 4"
are for. From the picture, I can't figure out where they go or what they're for.
Do these have something to do with the "Side" and "Back & Doors" views?
I basically want to implement this design with a 400W HID (http://htgsupply.com/growlights.asp?categoryID=1&subcategoryID=155&typeID=55) , a Rubbermaid DWC, a 6" inline Fan connected at the top (much like Scrub's bathroom fan) @ 250 CFM (http://htgsupply.com/viewproduct.asp?productID=46447) connected to some 6" or 4" ducting, (I'd love to hear some comments on the merits of both, regarding pressure for the carbon scrubber, etc), utilizing a carbon filter.
One problem I'm concerned about is how I can route the power from my ballast to my lamp when the cable between them doesn't unplug. Is there a problem created by this or am I missing something?
Parts I already have:
*400W HID/ballast
*6" Inline fan linked to above.
*6 50 CFM 80mm Computer Fans and a modded Power Supply connected to a toggle to turn on PSU without motherboard signal for powering fans.
Oh and the "dado" mentioned in the cabinet door, how do you cut that?
I'm a tad bit concerned I may not understand cabinet building enough to do this, but I think I may be overthinking this.
If someone could give me an idea of how this cabinet fits together, I'd really appreciate it.
Thanks,
windwalker
I'm attempting to copy Scrub's cabinet to use for flowering, with directions found here: https://www.rollitup.org/view.php?pg=faq&cmd=article&id=563 (along with handy dandy pictures) and am having a bit of trouble understanding the directions for building the cabinet. I really like the modular design though, and understand that there are two modules, one sitting above the main chamber and providing ventilation/power management and one sitting below the main chamber providing passive intake.
Later in the guide a carbon filter is added, although I don't quite understand how the top chamber is reworked.
I understand that there are:
3" diam black piping used for creating the light traps
6 ea 3/4" panels of plywood at 84" x 48"
a fan
ducting
bolts and screws
and hinges
and this seems simple enough, the six plywood sheets are cut up into the proper lengths to construct 3 boxes, but I don't quite see how they fit together.
what I don't understand is what the
8 ea 1x2 8' long
and 4 linear ft 1" x 4"
are for. From the picture, I can't figure out where they go or what they're for.
Do these have something to do with the "Side" and "Back & Doors" views?
I basically want to implement this design with a 400W HID (http://htgsupply.com/growlights.asp?categoryID=1&subcategoryID=155&typeID=55) , a Rubbermaid DWC, a 6" inline Fan connected at the top (much like Scrub's bathroom fan) @ 250 CFM (http://htgsupply.com/viewproduct.asp?productID=46447) connected to some 6" or 4" ducting, (I'd love to hear some comments on the merits of both, regarding pressure for the carbon scrubber, etc), utilizing a carbon filter.
One problem I'm concerned about is how I can route the power from my ballast to my lamp when the cable between them doesn't unplug. Is there a problem created by this or am I missing something?
Parts I already have:
*400W HID/ballast
*6" Inline fan linked to above.
*6 50 CFM 80mm Computer Fans and a modded Power Supply connected to a toggle to turn on PSU without motherboard signal for powering fans.
Oh and the "dado" mentioned in the cabinet door, how do you cut that?
I'm a tad bit concerned I may not understand cabinet building enough to do this, but I think I may be overthinking this.
If someone could give me an idea of how this cabinet fits together, I'd really appreciate it.
Thanks,
windwalker