Fixing LEDs?

MrToad69

MrToad69

Well-Known Member
@coreywebster

Hey gang or anyone..
I just wanted to reach out to some of the more "technical" lighting experts on the website...
I have 4 Meizhi 450's that I've been using for some time...The past couple years...The "grow switch"..on my lighting has died...Blue spectrum..wont flip on anymore..(Red grow still works) What is the most likely cause? Dead ballast? I deconstructed one of the lights..I see there are two ballast's inside..one for each switch obviously...If its the ballast, ...any recommendations for a cheap fix (replacement)Ballasts..just prefer not to throw them out...I need to refurbish 3 lights...
..And...what exactly am I looking for in the replacement ballast...What spec's have to be matched exactly...or is there some slight flexibility..power, resistance ..etc?
I can grow well...the build of the lights...not so much ..chuckle.

Are ballasts typically the weak link in a light system? Finite life?

Thanks in advance

Toad
 
Thanks AW

I'm rather attached to the 4 lights...gives me some versatility...

If people think its the ballasts...and I can buy some cheap generic replacements that will last 2-3 years great!

I appreciate the input, just looking to troubleshoot and source parts rather than looking for opinions on new gear..

Cheers
 
In those builds, the diodes being ran with too much amperage is generally more concern; at least as far as performance and longevity.
 
I guess my question, to be more specific...Do you think the ballasts are the issue? Is that more than likely why the grow side lights have died?

and where would be my most decent bet to buy replacement generic drivers ...ebay?

thanks
 
Power splices off into two separate ballasts..One to power grow..one to power flower...
This issue has has happen to 3 of my lights over the past couple years..Ive had these units for some time...As such, Im guess its the ballast..not sure though.

I have a multimeter..but clueless how to use it..
 
Thanks gang..just heading out to do some errands...I'll tinker with that later this afternoon and see how I make out ..Much appreciated :)
 
Moflow..

when I'm looking at specs...Do these driver have a general "range" they can operate in?

I guess I can have options...Guessing I can have a driver that operates at "lets say" 80% capacity..or another that is totally maxed to run the lights
 
MrToad69 said:
Moflow..

when I'm looking at specs...Do these driver have a general "range" they can operate in?

I guess I can have options...Guessing I can have a driver that operates at "lets say" 80% capacity..or another that is totally maxed to run the lights
Click to expand...
Depends on driver, mo is talking about a constant current driver i gather. Best to just get pics and it can usually be sorted.
 
MrToad69 said:
Power splices off into two separate ballasts..One to power grow..one to power flower...
This issue has has happen to 3 of my lights over the past couple years..Ive had these units for some time...As such, Im guess its the ballast..not sure though.

I have a multimeter..but clueless how to use it..
Click to expand...
Are the ac electrical connectors to each of the drivers the same?
If so, just switch the circuits and see if it follows the other led section.
That will tell you if it's the driver or the ac switch side.
The drivers usually have input and output specs listed on them.
See if it has 120v ac on the input side and whatever dc voltage the driver specs list.
 
Question...wondering what may have caused my ballast issues...Can freezing temps hurt ballasts? I stored a couple days in garage this winter..got down to -30C for a few days
 
MrToad69 said:
Question...wondering what may have caused my ballast issues...Can freezing temps hurt ballasts? I stored a couple days in garage this winter..got down to -30C for a few days
Click to expand...
Yes for sure. Solder joints can crack. Just type in what you are on the driver in to Google and you'll get results usually. If not, we can link you to some off of eBay that will work if you can take some pics of the labeling on the drivers
 
Airwalker16 said:
Yes for sure. Solder joints can crack. Just type in what you are on the driver in to Google and you'll get results usually. If not, we can link you to some off of eBay that will work if you can take some pics of the labeling on the drivers
Click to expand...
Thank you
 
Well I opened it up...and this is what I see...The switches..Bloom is connected to first ballast photo(ending with BQ-F) and the vegetation switch is connected to the second photo (ending in AQ-F...also labelled B) I believe the 4th photo labelled B is the problem..Looks like these are totally different drivers..Anyone able to explain..would be appreciated :)

Can anyone recommend any cheap ebay options or otherwise?

Thanks
 

Attachments

  • B782B1AB-CCFE-4B78-A5D4-F482380D01EC.jpeg
    B782B1AB-CCFE-4B78-A5D4-F482380D01EC.jpeg
    143.9 KB · Views: 29
  • C475316D-048E-44A5-8345-31A4F3AD1FE2.jpeg
    C475316D-048E-44A5-8345-31A4F3AD1FE2.jpeg
    100.3 KB · Views: 29
  • D7473A38-967E-4FC2-AEF8-D38702167D01.jpeg
    D7473A38-967E-4FC2-AEF8-D38702167D01.jpeg
    117.2 KB · Views: 29
  • BC917C24-553C-4B42-8549-382E227865CC.jpeg
    BC917C24-553C-4B42-8549-382E227865CC.jpeg
    148.6 KB · Views: 27
You must log in or register to reply here.
Back
Top