Hydro: Best way to change water?

randybishop

randybishop

Well-Known Member
Growing with DWC buckets.
What is the best way to siphon old water out to change water? I can't lift the plant because it is in a SCROG setup.

Like to know your thoughts. Thx!
 
vostok

vostok

Well-Known Member
At the initial planning stage most dwc pilots do realize that at some stage much water will be flowing in or out, and add a drain away in a drain in the center of the room, which they continually trip over ...lol
If nothing else look to a garden hose and a drill pump attached to your workshop drill
 
randybishop

randybishop

Well-Known Member
dbkick said:
Surely you can lift the bucket lids far enough to drop a submersible pump with a hose on it. If it's tight get a really small pump , drop the pump in put the hose where it dumps into an empty bucket and repeat for as many buckets as you have.
Click to expand...
What kind of pump would you suggest?
Would something like this pump the water out?
 
Metasynth

Metasynth

Well-Known Member
While a drill pump is simpler, I've been using submersible pumps to pump water out of DWC, and in my Ebb n Flow tables for years now without problems. Some pumps don't last forever, but they're not really that expensive. .And I've had a couple pumps running for years with no problems.
 
hydroMD

hydroMD

Well-Known Member
Empty your water anyway you can, then istall a bulkhead fitting with hose connected to an external res. You can then run a circulating pump from the res pumping back over your plant.


Now u just srain from the open bucket without disturbing your plant.


Its not a huge deal shuffeling a plant around to change water, but any stress has an affect on overall quality
 
dbkick

dbkick

Well-Known Member
hydroMD said:
Ps. What contaminates would u be afraid of with a an electric motor?
Click to expand...
Especially an electric motor that you can drop in a bucket of straight 35 percent h2o2 and pump away if you feel it's needed. nothing lives.
Afterthought , if you do this remember 35 percent h2o2 will pretty much take your skin off. Wear proper safety gear OR dilute down to a realistic concentration of h2o2.
 
N

natec631

Member
waterdawg

waterdawg

Well-Known Member
The pump you asked about would work if you filled the intake with water, they need to be primed. Get a small one and just lift corner as suggested. Also forget the siphon thing unless your pails are raised off floor as your hose output has to be lower than intake. Next run, move pails off floor a bit and add fittings. I have a barbed fitting at bottom of res's with a hose attached that I keep up-rite until drain time.
 
hydrogreen65

hydrogreen65

Well-Known Member
dbkick said:
Surely you can lift the bucket lids far enough to drop a submersible pump with a hose on it. If it's tight get a really small pump , drop the pump in put the hose where it dumps into an empty bucket and repeat for as many buckets as you have.
Click to expand...
Works like a charm. I drain my big reses same way. I just switch output on pump to a garden hose and water the bushes out fro t with it. Lol
 
Red1966

Red1966

Well-Known Member
randybishop said:
Thanks for all the good suggestions!
One more question, would a pump like this work outside the bucket to siphon the water out?
>>product link<<

Click to expand...
Be aware a submersible pump has to be IN the water to work. They need water in the pump cavity to work. A wet/dry vac will pull the water out from the top. Will suck up your roots too if you're not careful.
 
hydroMD

hydroMD

Well-Known Member
Bro, save yourself the headache and attach an external reservoir, attach all your buckets, and run a small pump to recirculate. U can pop lids off and drop pumps into buckets every weeks, but your disturbing your plants when you do it, even if its miniscule.

20140731_194534.jpg

20140731_190758.jpg

pump runs water to the back two buckets and flows back through to the res.

Once things are in full gear ill add ine more pump to recirculate the water in the res... when I change water i just attach a hose to it and drain the water. One pump to turn on, ten minutes later unhook your hose and refill.

Trust me, its the way to go.

I also add a fresh water top off with a float valve to keep things comoletely steady
 
hydroMD

hydroMD

Well-Known Member
20140731_190821.jpg
Use L fitting to keep hose from kinking.


20140729_210445.jpg
These are the bulkhead fittings i ordered.

1-1/4" spade bit is the perfect size for drilling your buckets.

DONT GET SMALLER THAN 1"!!!

drains too slow and can cause uneven bucket levels (makes a water top off unviable)
 
You must log in or register to reply here.
Top