doublejj's next big adventure....Lone Oak Farms 2016

[Vnsmkr]

The shit stain that he is, I wouldnt blame anyone for doing so

 

[ruby fruit]

The shit stain that he is, I wouldnt blame anyone for doing so

It gives me the same satisfying feeling as dropping a fart in a shoping aisle and watching some sexy chick walk into it

 

[Vnsmkr]

Dude I just had a good belly laugh there

 

[TWS]

Black live matters is no better than the KKK.
They need to butt fuck each other and make little half breeds so we can all get along.

 

[Vnsmkr]

Its all bullshit. Shiny object to keep peoples attention off of the real bullshit which goes on daily

 

[Vnsmkr]

If I click on "new posts" I can see a lot of this "IGNORED MEMBER" so that must mean uncle fuck is over there commenting now, fucking oxygen thief

 

[TWS]

You know you like to go over, call uncle fuck a fuck and haul ass

I can and don't even have to listen to him cry .

 

[doublejj]

do not buy ^^^ they have somer serious problems and all of them leak fluid.

I think I figured out why these have problems. They are pneumatic and have a max pressure of #2000 lbs. It takes more pressure to get a good squish, so people are maxing this unit each press & soon the seals fail.

 

[Vnsmkr]

Yip misuse I would say. I know they are a grand more but those sasquash presses have been reinforced and they tell you to limit your air pressure to max 85 psi.......
Air operated hydraulic
These hydraulics are welded to prevent leaks from happening. They are quite and operate very
smooth, also short to reduce size and weight of entire unit.
Welded release handle
20 Ton
Operating air pressure: 70-85psi, DO NOT EXCEED 85psi.
• Upper platen assembly
Welded to hydraulic, has hoops for lifting springs and plate for attaching upper platen. Two large
pipes fully welded for even spread of pressure, and to prevent heat traveling to hydraulic and frame

 

[doublejj]

I'm looking at a 20 ton Harbor freight shop press & some added heated plates..$199
http://www.harborfreight.com/20-ton-shop-press-32879.html

 

[Larry {the} Gardener]

I'm looking at a 20 ton Harbor freight shop press & some added heated plates..$199
http://www.harborfreight.com/20-ton-shop-press-32879.html
View attachment 3733331

I spend a little time on tractorbynet, and there is a thread on there called "Harbor Freight tools that don't suck." You may have to add yours once you get it rigged.

 

[Vnsmkr]

I'm looking at a 20 ton Harbor freight shop press & some added heated plates..$199
http://www.harborfreight.com/20-ton-shop-press-32879.html
View attachment 3733331

Alot of people have gone this route I think.....Heres a thread I just found, quite long....https://www.rollitup.org/t/rosin-tech.869445/page-36#post-12314217

 

[doublejj]

Low Temp heated plates with controller....$550
Made to bolt onto a shop press

 

[TWS]

The knd for license plates ?

 

[doublejj]

The knd for license plates ?

Kinda....but not really

 

[TWS]

 

[Vnsmkr]

What does walking a pig have to do with chase taking your money?

 

[Vnsmkr]

Must have some fukn inner meaning for advertising people to put it out there

 

[Olive Drab Green]

I guess where Im coming from the autopilot function had nothing to do with this......you get side swiped and run over by an 18 wheeler, well your fucked anyway

could have been a yugo, fucking media

He didn't get T-boned, he drove into it because the autopilot didn't contrast the trailer against the sky and it saw the trailer as part of the sky.

 

[Vnsmkr]

Yeah I saw that too at a later point. Maybe its just me but autopilot is fucking dumb. Lazy ignorant humans