Airwalker16
Well-Known Member
Just buy a short interval timer on Amazon. They're $10.
OK, but does that have a light sensor as well?Just buy a short interval timer on Amazon. They're $10.
Sure does if you get the century. Or the Titan controller. They're only $30=OK, but does that have a light sensor as well?
I think it is important that the timer reacts to 'lights out'.
Otherwise there is a chance that the far red leds will be turned on when your main lights are still on.
This one only will work like this:
Just do it the way I do it.This one only will work like this:
ON & OFF REPEATED: Set your appliance to cycle in intervals, turning on between 5sec - 30min, and off between 5sec - 60min
So when your main lights will turn off, perhaps this timer will turn on your far red leds. They will stay on for example for 5 minutes and then turn off. But after a maximum interval of 60 minutes they will be turned on again. That is not what you want.
You need a timer that 'recognises' that the main lights are off, and then immediately will turn on the far red leds for 1,2, 5, 10 or 15 minutes. And then will turn off, and will not be turned on again for 24 hours.
On Amazon I did not find such a timer.
So you have an overlap of 5 minutes? (where both your main lights and far red lights are on)Just do it the way I do it.
I waited 5 minutes, then manually turned the main light timer to click off. Far reds stay on for 10 more minutes.
Yep. That's right. Plus I've used these same harbor freight timers for years with zero issues. I think just running a good power Brick surge protector off it to plug everything into is the way to go.If they stay synced this is a good way to do it.
But I am wondering if they are that perfect. They look so simple.
But to be honest, I never timed them.
I modified a lot of timers (the ones with the pins) from 24 hours timers to 38 minute timers. And when you open them up, it looks like some plastic stuf that you expect in a cheap toy.
So you have an overlap of 5 minutes? (where both your main lights and far red lights are on)
Those are the Exact ones I was mentioning at first. They come with Orange Buttons, tooI have two of these timers (https://www.amazon.com/Multifunctional-Infinite-Programmable-Appliances-Energy-saving/dp/B01G6O28NA/ref=sr_1_1?crid=12I9Z7SSJMEN6&keywords=nearpow+timer&qid=1554340601&s=gateway&sprefix=nearpow+,aps,248&sr=8-1) and plan on using it to make a new far red light until I get an answer from hlg on where to buy the photosensitive circuit.
You can set those timers to go on after lights go out for even a second if you wanted to. They can be programmed to go on for up to 3 times a day. I was initially going to use them for drip irrigation but 3 daily timings was too low.
Yes they are complete crap inside but the most critical part, the frequency standard, comes from the power and is identical for both timers.If they stay synced this is a good way to do it.
But I am wondering if they are that perfect. They look so simple.
But to be honest, I never timed them.
I modified a lot of timers (the ones with the pins) from 24 hours timers to 38 minute timers. And when you open them up, it looks like some plastic stuf that you expect in a cheap toy.
Why would you do that?I’ll shut off the light at the end of their day and I’ll give them 24-36 hours of dark.
Ive never heard of that. Ive heard that plants in 20/4 light schedule do initiate flower faster so id have to look into it.It is commonly believed that 24-36 hours of darkness will speed the flowering initiation process. Do you think otherwise?
That's right, mechanical timers have synchronous motors and the AC frequency is very closely controlled.... generators on a grid must stay in phase!Yes they are complete crap inside but the most critical part, the frequency standard, comes from the power and is identical for both timers.
At least thats how I think they work, using the AC frequency to drive the mechanism.