Runtz try three

(If you're buying soil that's stored outside vs inside then it'll likely have bugs )

I think it's luck of the draw. If a filthy, bug infested grower walks into a hydro shop the hydro shop becomes contaminated.

Thanks for the tip.
 
Yes, I know. I fear bugs with FFOF and nute burn with Pro-Mix. :)
One test for this problem that I read about and have tried is to test some of the soil before using it. Take a sample from the bag, put in a sealed jar with some water. If critters are present, they should be visible in the jar after a day or so. I have tested soil this way, but never had critters indoors (using fax farm on the east coast, fwiw), so can’t confirm how effective it might be. Made sense to me though.
 
Yes, I know. I fear bugs with FFOF and nute burn with Pro-Mix. :)
At least on here, I feel like I see more folks with nute-burned plants using FFOF than anything else. The concept of "it has enough food for x number of weeks, then start adding fertilizer" just seems very tricky to get right, and the value of "x" is totally dependent on container size and plant size. Then when you start feeding, the soil isn't totally depleted of nutrients, so it's hard to know exactly how much to give without going overboard.

Pro-mix has very little nutrition to start with, so I figure it might be easier to work with, at least in terms of fertilization. Don't take my word for it though, the few times I tried feeding liquid/salt nutes were pretty rough. I have since switched to organic dry amendments and try to keep it water-only as much as possible.

Also you can pretty much turn that pro-mix into FFOF (or better) by adding worm castings and some Garden-Tone or Gaia 444 or similar...
 
I think the problems have been environmental and not ferts/soil or watering.

Before deploying the Inkbirds the equipment was more or less randomly turning on and off.

The humidifier was hooked to a timer set to 15 min on/15 min off. Now RH is consistently within a 5% range.
The thermostat controller on the oil heaters aren't precise enough for our application so that was randomly turning on and off. Now temp is consistently within a 3°F range.
Without the light meter the plants were being over saturated with light, according to the DLI document.

The thermostat/humidistat I was using was cheap junk and didn't even read right.

I can go on. :)
 
I think the problems have been environmental and not ferts/soil or watering.

Before deploying the Inkbirds the equipment was more or less randomly turning on and off.

The humidifier was hooked to a timer set to 15 min on/15 min off. Now RH is consistently within a 5% range.
The thermostat controller on the oil heaters aren't precise enough for our application so that was randomly turning on and off. Now temp is consistently within a 3°F range.
Without the light meter the plants were being over saturated with light, according to the DLI document.

The thermostat/humidistat I was using was cheap junk and didn't even read right.

I can go on. :)
You can't fix what you don't know...or something
 
I've been checking out the AC Infinity website and have a question.

The specs for Controllers 67 & 69 indicate "App Control and Data".

Is the data portion only live data while accessing the unit or
do these controllers have memory/MicroSD port with the ability to save or D/L spans of information?
 
I've been checking out the AC Infinity website and have a question.

The specs for Controllers 67 & 69 indicate "App Control and Data".

Is the data portion only live data while accessing the unit or
do these controllers have memory/MicroSD port with the ability to save or D/L spans of information?
They hold live and historical data accisible through the app.
Screenshot_20230223-210218.png
 
They hold live and historical data

Thanxx.

I found the DATA Tab as you were posting. I kept searching for memory.

"Temperature and humidity distribution are represented by bar graphs and tell you the most common climate condition within a given time interval. You can export this data as a CSV spreadsheet file to log and track it on your PC. "
 
Of all the things I can change I think more light is needed.

Not a lot of new growth from the topping.

Thoughts?
 

Attachments

  • 20230226_083839.jpg
    20230226_083839.jpg
    1.5 MB · Views: 19
  • 20230226_083845.jpg
    20230226_083845.jpg
    1.6 MB · Views: 19
  • 20230226_083850.jpg
    20230226_083850.jpg
    2 MB · Views: 19
These pics were taken in direct sunlight.

When I take pics under the LED light color temps seem to change. It's a Samsung phone.
 

Attachments

  • 20230226_092912.jpg
    20230226_092912.jpg
    1.9 MB · Views: 17
  • 20230226_092919.jpg
    20230226_092919.jpg
    1.9 MB · Views: 17
  • 20230226_092933.jpg
    20230226_092933.jpg
    1.6 MB · Views: 15
The plants look darker green since turning up the light but still a little funky..

Should I go 100% with the light?
 

Attachments

  • 20230228_073331.jpg
    20230228_073331.jpg
    2 MB · Views: 20
  • 20230228_073342.jpg
    20230228_073342.jpg
    1.6 MB · Views: 21
  • 20230228_073351.jpg
    20230228_073351.jpg
    1.7 MB · Views: 20
Back
Top