Homemade smoking devices

[captin stoner(:]

ok all these people are telling you such complicated stuff. i have one that is an actual smoking device and it will mess you up for only a little weed.

you need:
4mm socket
2 liter bottle
bucket of water
knife or scissors
of course weed and a lighter

1. get a 2 liter bottle (they work best but you can experiment with any bottle)
2. cut the very bottom off so it doesnt have a bottom at all.
3. get the cap and poke a hole in it and just keep cutting it until the 4mm socket fits in it tightly. then fill with weed
4. take the cap off the bottle and put it in the bucket of water up to the neck of the bottle.
5. put the cap on the bottle
6. light the weed as you pull up on it
7. when all the water is out of the bottle and its full of smoke take the cap off and inhale while you push it back into the water.
8. and finally cough your ass of for a few minutes and then trip ass

 

[noober doober]

LOL! Ok, one of my all time greates devices (and there were a few, including a dual engine bong : )) Ok, so you know how a gravity bong works right? I haven't read the thread but I'm sure someone mentioned it. Well, I took a huge trash barrell (air tight of course) and drilled a little hole in the top big enough for a "liberty bowl" or a blunt works too. Place the trash barrell upside down in a pool and push it down so it's like 3/4 submerged. Screw in packed bowl or lit blunt and two people slowly pull the barrell up (filling it with smoke). Then..... swim underneath and inside the barrell for your hits!!!! Careful though, it hits hard and you still have to swim out without drowing if you are coughing your brains out : )) Was going to make a clear one and send into high times or something back in the day.. sorry no pics, haven't done this in a long time.

edit** just realized the post above me is describing a gravity bong lol

 

[RollBluntsUp420]

This is my bamboo Blunt/Joint ash catcher. Hits very harshly but i love it. I used a drill to make the carb and a saw for the rest. You put a lit blunt with a matching sized end into the side with the catcher and smoke it like a pipe. Hope you like it.

 

[thegersman]

I think I went overboard on this one.........


SORRY!

 

[RollBluntsUp420]

You guys have been awesome the list is getting huge. Check it out and see if your invention is there. GrowFAQ, DIY and save, click on page 2 (it's that long we needed a second page!)

Am I retarded or is it not there? I'm not even high yet shit.

 

[RollBluntsUp420]

I think I went overboard on this one.........

You probably wont get a hit until about a month after you burn it haha.

 

[1hashslingingslasher1]

What matials did you use for your bunt?

 

[dragnit]

Here is a pipe I made like twenty years ago. Made from Hazelnut tree. Hazelnut has a corky soft hole in the middle so you can easily run a hot wire down the middle to make the stem. Still one of my favorite pipes.

 

[PinkBeautyKiller]

this is the easiest homade peice all you need is tinfoil and a pen, or anything that is shaped like a pen.
1, rip off a peice of foil that is about 4 inches wide
2 fold in half
3 fold one edge over
4 place finger where you folded over and pen to the tip of your finger
5 roll the foil arould the pen and your finger
6 squeze foil tight around the pen and your finger
7 pull out pen and finger bend, and enjoy,

now youll never be without something to smoke,

what do you think of that mogie, growfaqworthy??

the last two pics are on the next post

how do you smoke with it??
do you put the tin foil back onto the pen and put the weed in the tin foil then lite it or??

 

[PinkBeautyKiller]

Am I retarded or is it not there? I'm not even high yet shit.

i cant find it either

 

[Isaiah Porter]

One time I took an Amsterdam (pint) bottle, pierced a hole in the center of the cap with a pen. Then I took a knife and turned it inside of the hole (to maintain an even circle) until it was just under the size of the bowl piece I was using. (45. ACP bullet casing. I used a hammer and nail to push out the striker thingy on the back ) then I inserted the bowl piece and put a little play dough around the base. I then took a pen and made a much smaller hole next to the original and inserted an 8" piece of tubing from an air filter. If I find a pic I'll make sure to upload it