4 32 site xl undercurrent systems in a 20X40 room

how's set up going?
Yes been so dam busy with my reg job and the grow. Wish i was further along but just got my outlets wired last night. Bringing ac guy in next day or so. Have one system built so far. Kind of tough to set up. My damm thumb is so sore from pushing rubber air hose seals into 32 buckets. Lol. Here are pix of my first system built.
 

Attachments

  • IMG_20191005_180245_01.jpg
    IMG_20191005_180245_01.jpg
    2.3 MB · Views: 85
  • IMG_20191006_193415_01.jpg
    IMG_20191006_193415_01.jpg
    3 MB · Views: 87
  • IMG_20191006_193518_01.jpg
    IMG_20191006_193518_01.jpg
    2.9 MB · Views: 85
Sux i wont have enough clones to put in to all 3 systems when i start. Thx to the 128 sute ez cloner fuckin with me. Not worried tho. Wont be to long before all 3 are running at same time.
 
Had the first system running chiller and all. Stupid drain kit valve was open and i didnt notice until it was everywhere. I was pluggin in air lines and look up with a few gallons on floor. The system used to come with an inline filter closer to the pump from what i remembered. Now there are 4 little bulkhead screens to put on return manifold to catch debris. I will probably start it with plants on tuesday., have to wait for hvac guy to install the lines. Electrician is done.
 
Well i just couldnt wait any longer. Had to throw down a test run to play with and get a feel for the uc. The clones are in and i dont even have my ac going. 60% power 82f with 8 lights. Been cooler outside tho
 

Attachments

  • 20191013_181326.jpg
    20191013_181326.jpg
    2.5 MB · Views: 63
  • 20191013_181311.jpg
    20191013_181311.jpg
    2.6 MB · Views: 60
Not quite 24hrs in and they looking good. All standing up straingh some root making its way out of the net pots. Ppm 160 water temp 66f room 80f and o2 pressure at 25
 
With that O2 pressure your nutes may be high. Keep a close watch for rust spots, like a cal-mag deficiency. In this system that means there's too much. Drop your ppm's down to 100 FAST if you see that happening. According to the feeding chart I should be at 980 but I'm just easing past 700 with that O2 pressure.
 
Ph rose from 6.1 to 6.4 over night. Ppm went up to 200. The plas
With that O2 pressure your nutes may be high. Keep a close watch for rust spots, like a cal-mag deficiency. In this system that means there's too much. Drop your ppm's down to 100 FAST if you see that happening. According to the feeding chart I should be at 980 but I'm just easing past 700 with that O2 pressure.
Should i lower the o2 pressure?
 
Next day.
 

Attachments

  • 20191020_132821.jpg
    20191020_132821.jpg
    933.7 KB · Views: 17
  • 20191020_132706.jpg
    20191020_132706.jpg
    706.9 KB · Views: 17
  • 20191020_132650.jpg
    20191020_132650.jpg
    749.7 KB · Views: 14
Ppm is down to 100. Havent hooked up top off res yet. Got to figure out how i want to do it. Got smaller wort chiller because the ones i have are to big to allow the float valve to work.
 
This system really has the most explosive growth i have expirenced. I was looking on live video with adt and really cant wait to get to my shop. I need to start my co2 generator but need ac hooked up first. I know its early and you can lose it quick so im not going to let my guard down until im chopping them down.
 
Pixxx from today
 

Attachments

  • 20191021_214738.jpg
    20191021_214738.jpg
    2.4 MB · Views: 43
  • 20191021_214735.jpg
    20191021_214735.jpg
    2.4 MB · Views: 40
  • 20191021_203122.jpg
    20191021_203122.jpg
    653.4 KB · Views: 39
  • 20191021_203122.jpg
    20191021_203122.jpg
    653.4 KB · Views: 39
  • 20191021_214738.jpg
    20191021_214738.jpg
    2.4 MB · Views: 40
  • 20191020_193829.jpg
    20191020_193829.jpg
    2.3 MB · Views: 39
Back
Top