Dollar Store Grow Lights!

THC-CK

THC-CK

Well-Known Member
So, while venturing the isles of the local dollarstore I came across these babies! Now, I know they are only 9w but, but used in conjunction with other lighting, or by itself in multiples, it seems like a a viable option for those on a budget!

I cracked them open to see what was inside, it consists of 6 x 600-700nm chips, and 2 x 400-500nm chips.

I was looking to lower the output of my veg LED setup, and swapped three of these into a splitter. We shall see how she likes them!
 

Attachments

  • 20191230_152746~2.jpg
    20191230_152746~2.jpg
    1.5 MB · Views: 136
  • 20191230_152753~2.jpg
    20191230_152753~2.jpg
    1.4 MB · Views: 149
  • 20191230_152706.jpg
    20191230_152706.jpg
    2.4 MB · Views: 143
Man I wish much dollar store offered such goods. Try them out I grow on a budget, even using egg shells, Epson salt, and baking soda. Stuff laying around. My plants are pretty happy on the cheap.
 

Attachments

  • 20191229_140359.jpg
    20191229_140359.jpg
    867.2 KB · Views: 74
  • 20191229_140424.jpg
    20191229_140424.jpg
    884.6 KB · Views: 76
  • 20191229_140406.jpg
    20191229_140406.jpg
    913.3 KB · Views: 74
Chip Green said:
Whites alone can get it done, lookie here...
https://www.rollitup.org/t/screw-in-grow.957051/
Click to expand...

Awesome! Once they are in flower I'm going to be using a Mars TS600, but for veg and future micros I'm very impressed with the screw in LEDs and will continue to use them.

I had 7 x 16w (A21 size) 2700K and 3000K bulbs and it was too much light for one plant. I had it much too close and stressed the crap out of her. Fingers crossed she will recover.
 
Update:

So, after doing some light meter testing, and seeing the plant "like" them, I decided to switch the entire splitter over to 7 of these.

9 x 7 = 56w draw

It is putting out roughly 9200 lux, so maybe 500umol give or take?!

Not bad for veg!
 

Attachments

  • 20191231_131832~2.jpg
    20191231_131832~2.jpg
    2.7 MB · Views: 76
THC-CK said:
So, while venturing the isles of the local dollarstore I came across these babies! Now, I know they are only 9w but, but used in conjunction with other lighting, or by itself in multiples, it seems like a a viable option for those on a budget!

I cracked them open to see what was inside, it consists of 6 x 600-700nm chips, and 2 x 400-500nm chips.

I was looking to lower the output of my veg LED setup, and swapped three of these into a splitter. We shall see how she likes them!
Click to expand...
what name of dollar store was it?
 
Update 2:

They gone.

I came home to check on her tonight and o noticed that the lights just didn't "look" as bright. So, I thought I'd pull out my light meter... 3200 lux at the exact same distance as yesterday.

I have swapped the 7 x 16w 3000K bulbs back in and raised it up to 18" exactly now. We will see how she does.

Disappointed... But not surprised to say the least.
 
THC-CK said:
Update 2:

They gone.

I came home to check on her tonight and o noticed that the lights just didn't "look" as bright. So, I thought I'd pull out my light meter... 3200 lux at the exact same distance as yesterday.

I have swapped the 7 x 16w 3000K bulbs back in and raised it up to 18" exactly now. We will see how she does.

Disappointed... But not surprised to say the least.
Click to expand...
Prolly getting too hot, and dimming down.
 
I did a similar thing, but stripped the little plates holding the LEDs off and mounted them on side of old PC case...just the side, not the whole case...lol
I found this way the heat was better controlled and went from about 35+ degrees down to nice constant 28"
The ones I found run at 60v (dc) so I linked 2 together in series into an 8Amp bridge rectifier and couple resistors straight from the wall...no "driver"...about 90-100 VDC comes out and I just paralleled 8 pairs for a total of 16 bulbs.
Biggest failures of the LED bulbs I found were the crappy "drivers" they use in them...they fail very easily.
Try to find "Dimmable" bulbs...they dont use extra circuits on the LED board for voltage dropping and can be easily combined and run from a driver.
Will try to snap a pic tomorrow for ya.

Oh ya if your not using them now why not open 1 up completely...to see how it ticks :P
 
THC-CK said:
Awesome! Once they are in flower I'm going to be using a Mars TS600, but for veg and future micros I'm very impressed with the screw in LEDs and will continue to use them.

I had 7 x 16w (A21 size) 2700K and 3000K bulbs and it was too much light for one plant. I had it much too close and stressed the crap out of her. Fingers crossed she will recover.
Click to expand...
How big an area are you going to flower in?
The TS600 is actually a really clever light bit will only flower like a 1.5'X1.5' area. 2'X2' if you're in a good tent.
Bit the cool thing about the TS600 is that it doesn't even have a driver. It's just got enough resistors and other Surface mounted components on it to where it just uses mains 120V power. It can't even be used in the UK or 240V AC.
 
Airwalker16 said:
How big an area are you going to flower in?
The TS600 is actually a really clever light bit will only flower like a 1.5'X1.5' area. 2'X2' if you're in a good tent.
Bit the cool thing about the TS600 is that it doesn't even have a driver. It's just got enough resistors and other Surface mounted components on it to where it just uses mains 120V power. It can't even be used in the UK or 240V AC.
Click to expand...

It's a 3x3 tent. I plan to do a one or two plant perpetual DWC grow.

The more research I do I'm leaning towards the Spiderfarmer or the Mars TS1000 due to the driver.

I'm also tempted to look at CMH now that they are so cheap. A good vertical setup can be had for $250.
 
Mak'er Grow said:
I did a similar thing, but stripped the little plates holding the LEDs off and mounted them on side of old PC case...just the side, not the whole case...lol
I found this way the heat was better controlled and went from about 35+ degrees down to nice constant 28"
The ones I found run at 60v (dc) so I linked 2 together in series into an 8Amp bridge rectifier and couple resistors straight from the wall...no "driver"...about 90-100 VDC comes out and I just paralleled 8 pairs for a total of 16 bulbs.
Biggest failures of the LED bulbs I found were the crappy "drivers" they use in them...they fail very easily.
Try to find "Dimmable" bulbs...they dont use extra circuits on the LED board for voltage dropping and can be easily combined and run from a driver.
Will try to snap a pic tomorrow for ya.

Oh ya if your not using them now why not open 1 up completely...to see how it ticks :P
Click to expand...

Now that I have the 16w bulbs back in there I may take some time and pull apart one of those blurples to take a peak see.

I think you are correct as well. The blurples are non-dimmable, however; the 2700K and 3000K units are dimmable.
 
You must log in or register to reply here.
Back
Top