R&RHashman
Well-Known Member
thanks Sir and Chew
Hash and Oil Picture Thread
- Thread starter Sirdabsalot462
- Start date
Guzias1
Well-Known Member
beautiful, and nice yield!
R&RHashman
Well-Known Member
why 180p everclear and not iso 91% ?? I did a few frozen trim runs , didn't notice that much of a difference
Texas(THC)
Well-Known Member
Girl Scout Cookie Wax
R&RHashman
Well-Known Member
looking sweet THC ! +1 like
Texas(THC)
Well-Known Member
Thanks everyone
lio lacidem
Well-Known Member
Very nice texas! Very nice
blackforest
Well-Known Member
Texas(THC)
Well-Known Member
Cleaned My Pyrex Today
Sirdabsalot462
Well-Known Member
Looking fire boys....
Thank you all for keeping this thread as popular as it is.
Mas peeek-churzzzz
All cured material...
1 oz in 4.6 out
^ Fresh out da chay-buh...
More pics when she finished ” curing” into a glassy ” square.
Man, as I was folding this batch into a square...
Even after warming the section to fold....” Crunch”...shatter snapping sent shards everywhere..
Prolly closer to 5 ish grams
Thank you all for keeping this thread as popular as it is.
Mas peeek-churzzzz
All cured material...
1 oz in 4.6 out
^ Fresh out da chay-buh...
More pics when she finished ” curing” into a glassy ” square.
Man, as I was folding this batch into a square...
Even after warming the section to fold....” Crunch”...shatter snapping sent shards everywhere..
Prolly closer to 5 ish grams
Metasynth
Well-Known Member
I got you covered...my rep hand is stronger anyway...
Sirdabsalot462
Well-Known Member
Dayyummm...
Y'all got some rep POWER!!
lolz...
Thank you gentlemen!
I know when I say” curing” oil may be a bit confusing to those that don't make oil often.
But to clear things up..
When I refer to curing my oil..
Right after the chamber, the oil has a wet looking finish.
I fold my square inside a parchment envelope that is breathable..
After 12 hours or so the oil really” glasses” up and hardens even more.
Hey!!
Has anybody tried blasting directly onto the new Oil Slick Sheet? Not the Slick Pad
The slick sheet is a bit pricey, but made from PFTE.
Manufacture claims its safe to blast directly onto, but only once.
I'm sooooo sick of scraping...lol
I think it's about 20$ ish for a roll..if in bulk around 11$
With the popularity of hash oil skyrocketing, one would think that some company would have taken initiative to create a safe material to blast onto.
Y'all got some rep POWER!!
lolz...
Thank you gentlemen!
I know when I say” curing” oil may be a bit confusing to those that don't make oil often.
But to clear things up..
When I refer to curing my oil..
Right after the chamber, the oil has a wet looking finish.
I fold my square inside a parchment envelope that is breathable..
After 12 hours or so the oil really” glasses” up and hardens even more.
Hey!!
Has anybody tried blasting directly onto the new Oil Slick Sheet? Not the Slick Pad
The slick sheet is a bit pricey, but made from PFTE.
Manufacture claims its safe to blast directly onto, but only once.
I'm sooooo sick of scraping...lol
I think it's about 20$ ish for a roll..if in bulk around 11$
With the popularity of hash oil skyrocketing, one would think that some company would have taken initiative to create a safe material to blast onto.
Sirdabsalot462
Well-Known Member
Ha!!
I don't think I'll use ZHO for anything but removing dust from inconspicuous areas.
Maybe...I'll walk on sunshine..
Lol
lio lacidem
Well-Known Member
Why not lol? Everyone wants to use a solvent that turns to acid and phosgene when hits heat abd moisture. And is pretty toxic to boot? I just ordered a master case