AiCPearlJam
Well-Known Member
Just wondering if they are worth the $160+ price tag. What are the advantages besides light weight, not as hot and it's digital?
For cfls you don't need a ballast. A lighting ballast is necessary to operate high intensity discharge lights because they have negative resistance, meaning they are unable to regulate the amount of current that passes through them. A lighting ballast must be used to control current flow; otherwise the light could fail. Small light sources can use passive components, which require no additional power to operate, as ballasts. An example would be a series resistor that limits the flow of current across its terminals. For high-powered lights, however, a resistor would waste a large amount of electricity, so a more complex lighting ballast is required.I've been using CFLs so I have no idea about larger lights.. Is a ballast actually needed?? What is its function?
i think you are thinking of a resistor not a ballasti thought all CFL's did have a ballast? albeit a small one, its located at the base of the glass spiral, and its housed in plastic.
haha no i'm not an electrician just a simple overworked and underpaid mechanic. i try to study up on anything and everything that interests me.really? yea, now that i think about it, it would make more sense...i remember someone else on here called them a ballast, and i just though that all fluorescents had ballasts...but thanks for clearing that up. are you an electrician or something?
The desire of knowledge, like the thirst of riches, increases ever with the acquisition of it.i agree. knowledge is a very powerful tool...
CFL's need a ballast ...i think you are thinking of a resistor not a ballast
I stand corrected. I thought the op was asking if he could get a separate ballast for his cfl's. my badCFL's need a ballast ...
Parts
![]()
Electronic ballast of a compact fluorescent lamp
There are two main parts in a CFL: the gas-filled tube (also called bulb or burner) and the magnetic or electronic ballast. An electrical current from the ballast flows through the gas, causing it to emit ultraviolet light. The ultraviolet light then excites a phosphor coating on the inside of the tube. This coating emits visible light (see Fluorescent lamp).
Electronic ballasts contain a small circuit board with rectifiers, a filter capacitor and usually two switching transistors connected as a high-frequency resonant series DC to AC inverter. The resulting high frequency, around 40 kHz or higher, is applied to the lamp tube. Since the resonant converter tends to stabilize lamp current (and light produced) over a range of input voltages, standard CFLs do not respond well in dimming applications and special lamps are required for dimming service. CFLs that flicker when they start have magnetic ballasts; CFLs with electronic ballasts are now much more common.
[edit] Integrated CFLs
Integrated lamps combine a tube, an electronic ballast and either an Edison screw or bayonet fitting in a single CFL unit. These lamps allow consumers to replace incandescent lamps easily with CFLs. Integrated CFLs work well in standard incandescent light fixtures. This lowers the cost of CFL use, since they can reuse the existing infrastructure. In addition, incandescent light fixtures are relatively inexpensive. Special 3-way models and dimmable models with standard bases are available for use when those features are needed.[6]
[edit] Non-integrated CFLs
Non-integrated CFLs have a separate, replaceable bulb and a permanently installed ballast. Since the ballasts are placed in the light fixture they are larger and last longer, compared to the integrated ones. Non-integrated CFL housings can be both more expensive and sophisticated, providing options such as dimming, less flicker, faster starts, etc.[7][8]
The ballasts make these light fixtures relatively expensive. They cost anywhere from $85 to $200 USD for each recessed light fixture. If a ballast with dimming capabilities is desired the cost is anywhere from $125 to $300 USD per recessed light fixture. Non-integrated CFLs are more popular for professional users, such as hotels and office buildings. The more advanced capabilities of these sophisticated external ballasts (e.g., faster starts, limited flicker, dimming, longer lifespans, etc.) are starting to appear in integrated CFLs.
Another style of non-integrated fitting is the "two piece", where the initial system includes a base adapter and detachable fluorescent tube module, and subsequently only the tube unit is replaced. The Thorn 2D and some Philips PL versions are examples, but while replacement tubes are generally still available, it is rare to see the complete kit on sale, having been overshadowed by cut-price one-piece units.
![]()