Bong v.s. Pipe? discuss..........poll.

[bigbenzo420]

i know man..... so soothing, so refreshing..... i've been smoking out of a bottle bong since my glass piece broke. i'm the one bottle guy.

oh yeah post a pic of that contraption u speak of

 

[indianaman]

good ol' billy bottle. smokes like a champ.

 

[bigbenzo420]

good ol' billy bottle. smokes like a champ.

Dam not as bad i thought u got a glass stem in it, and cut it down a bit kool bro when i was younger i would just cut a hole in a bottle and cut a carb on the bottom put some aluminum foil over the hole and press down 2 create a bowl and go 2 work dam i was stupid peace

 

[KushKing949]

i bong it all the way or use my bubb

or save all the trichomie leaves that i pulled off the bud and wait till i have like 2 grams of that and roll a nice blunt to puff

 

["SICC"]

here what im usin

2 foot Jerome Baker, strait shot, RooR Diffuser, Matchin bowl, shes a beast

 

[herbie1020]

normally i will smoke a pipe just cuz its usually just me. but ill roll a blunt or joint often as well. but tonite i had none of the above, and not even foil so i made a pipe out of a mountain dew can and some sockets from the tool set. add a carb and a screen from the sink and good to go hehe. now i am FUKD up! didnt realize how much smoke you can fit in a 12oz can so ive been coughin for like 20 minutes now off that first hit hehe

 

[KushKing949]

very nice

 

[indianaman]

Dam not as bad i thought u got a glass stem in it, and cut it down a bit kool bro when i was younger i would just cut a hole in a bottle and cut a carb on the bottom put some aluminum foil over the hole and press down 2 create a bowl and go 2 work dam i was stupid peace

can't be too ghetto, you learn a thing or two after a few years of tinkering when you're not old enough to buy a proper piece. like the can stem? you have to have an actual glass bowl though.

 

["SICC"]

Yea its good to have those raw skills when the time calls, i can make a mean ass water bottle bong, Air tight every time haha

 

[indianaman]

no tape........... can't use tape man... mine's airtight. just heat up a pair of scissors and poke a hole and slowly make a perfect circle.... really handy skill.

 

["SICC"]

I can make the hole with jus a lighter, then stic your down stem in and your set, the key is to make the hole smaller then the stem, so when you stic it in, it a tight fitting

 

[Tryingtomastrkush]

[QUOTE="SICC";1951170]I can make the hole with jus a lighter, then stic your down stem in and your set, the key is to make the hole smaller then the stem, so when you stic it in, it a tight fitting[/QUOTE]

thats how i used to do it and if all else fails a good 3 layers of duct tape does the job

 

[indianaman]

I take a pair of scissors and take one cutting blade and heat it up over a candle. take the hot blade and poke a small hole in the bottle. take the cool side of the scissors<the sharper the better>and continue to slowly flake away the plastic making a perfectly round hole if you go slow enough. this takes a few times to master. i take the middle of a can and roll it up tight and stick the stem in it to see if it fits, then tie it so it stays in position and stick it in the hole.

 

[indianaman]

No Tape!!!

 

[Tryingtomastrkush]

fuck tape fixes everything

 

[indianaman]

makes bongs sticky. water makes it come off. don't put near your flame! toxic chemicals, looks tacky. do my method and rest assured that i have wasted many years of my life perfecting this method.

 

[Tryingtomastrkush]

fuck im not saying make the whole thing out of duct tape but 2 or 3 layers around where the stem enters the bottle wont get anything wet or on fire unless you got a really big gap and in that case you should make a new one

 

[indianaman]

read the post! works everytime.

 

[bigbenzo420]

I take a pair of scissors and take one cutting blade and heat it up over a candle. take the hot blade and poke a small hole in the bottle. take the cool side of the scissors<the sharper the better>and continue to slowly flake away the plastic making a perfectly round hole if you go slow enough. this takes a few times to master. i take the middle of a can and roll it up tight and stick the stem in it to see if it fits, then tie it so it stays in position and stick it in the hole.

Hey man thats pretty good job i couldnt even see the rolled up can in the pic, but that is a great idea ill remember that whenever my bong or bub break this pic is my array of smoking machines peace

 

[indianaman]

awww. you're gay. good looking pot. a can can go a long way my friend. you have been imparted with the knowledge of the master. i hope your pieces don't break... but if they do you are now prepared. i love those buds. my weed is lawn clippings compared to it....sigh. time for a bong hit.