Bong v.s. Pipe? discuss..........poll.

Pipe, Bong, or somewhere in between?

  • I prefer the pipe.

    Votes: 9 11.1%

  • I prefer the bong.

    Votes: 34 42.0%

  • I enjoy a nice joint.

    Votes: 13 16.0%

  • I enjoy a nice blunt.

    Votes: 6 7.4%

  • I prefer a vaporizer.

    Votes: 11 13.6%

  • I have a steamroller.

    Votes: 1 1.2%

  • I smoke out of a can.

    Votes: 0 0.0%

  • I smoke out of a bottle.

    Votes: 1 1.2%

  • I SMOKE ROCKS!!!!!!!!!!

    Votes: 6 7.4%

  • I dont smoke pot..(get outta here creamskimmers)

    Votes: 0 0.0%
  • Total voters
    81
indianaman said:
good ol' billy bottle. smokes like a champ.
Click to expand...

Dam not as bad i thought u got a glass stem in it, and cut it down a bit kool bro when i was younger i would just cut a hole in a bottle and cut a carb on the bottom put some aluminum foil over the hole and press down 2 create a bowl and go 2 work dam i was stupid peace
 
i bong it all the way or use my bubb

or save all the trichomie leaves that i pulled off the bud and wait till i have like 2 grams of that and roll a nice blunt to puff
 
here what im usin

bong.jpg



2 foot Jerome Baker, strait shot, RooR Diffuser, Matchin bowl, shes a beast bongsmilie
 
normally i will smoke a pipe just cuz its usually just me. but ill roll a blunt or joint often as well. but tonite i had none of the above, and not even foil so i made a pipe out of a mountain dew can and some sockets from the tool set. add a carb and a screen from the sink and good to go hehe. now i am FUKD up! :clap: didnt realize how much smoke you can fit in a 12oz can so ive been coughin for like 20 minutes now off that first hit hehe
 
bigbenzo420 said:
Dam not as bad i thought u got a glass stem in it, and cut it down a bit kool bro when i was younger i would just cut a hole in a bottle and cut a carb on the bottom put some aluminum foil over the hole and press down 2 create a bowl and go 2 work dam i was stupid peace
Click to expand...
can't be too ghetto, you learn a thing or two after a few years of tinkering when you're not old enough to buy a proper piece. like the can stem? you have to have an actual glass bowl though.
 
Yea its good to have those raw skills when the time calls, i can make a mean ass water bottle bong, Air tight every time haha
 
no tape........... can't use tape man... mine's airtight. just heat up a pair of scissors and poke a hole and slowly make a perfect circle.... really handy skill.
 
I can make the hole with jus a lighter, then stic your down stem in and your set, the key is to make the hole smaller then the stem, so when you stic it in, it a tight fitting
 
[QUOTE="SICC";1951170]I can make the hole with jus a lighter, then stic your down stem in and your set, the key is to make the hole smaller then the stem, so when you stic it in, it a tight fitting[/QUOTE]

thats how i used to do it and if all else fails a good 3 layers of duct tape does the job
 
I take a pair of scissors and take one cutting blade and heat it up over a candle. take the hot blade and poke a small hole in the bottle. take the cool side of the scissors<the sharper the better>and continue to slowly flake away the plastic making a perfectly round hole if you go slow enough. this takes a few times to master. i take the middle of a can and roll it up tight and stick the stem in it to see if it fits, then tie it so it stays in position and stick it in the hole.
 
makes bongs sticky. water makes it come off. don't put near your flame! toxic chemicals, looks tacky. do my method and rest assured that i have wasted many years of my life perfecting this method.
 
fuck im not saying make the whole thing out of duct tape but 2 or 3 layers around where the stem enters the bottle wont get anything wet or on fire unless you got a really big gap and in that case you should make a new one
 
indianaman said:
I take a pair of scissors and take one cutting blade and heat it up over a candle. take the hot blade and poke a small hole in the bottle. take the cool side of the scissors<the sharper the better>and continue to slowly flake away the plastic making a perfectly round hole if you go slow enough. this takes a few times to master. i take the middle of a can and roll it up tight and stick the stem in it to see if it fits, then tie it so it stays in position and stick it in the hole.
Click to expand...


Hey man thats pretty good job i couldnt even see the rolled up can in the pic, but that is a great idea ill remember that whenever my bong or bub break this pic is my array of smoking machines peace
 

Attachments

  • 003.jpg
    003.jpg
    40.6 KB · Views: 7
awww. you're gay. good looking pot. a can can go a long way my friend. you have been imparted with the knowledge of the master. i hope your pieces don't break... but if they do you are now prepared. i love those buds. my weed is lawn clippings compared to it....sigh. time for a bong hit.
 

Attachments

  • l_a047a4e5140149da8e74f99d24777d3e.jpg
    l_a047a4e5140149da8e74f99d24777d3e.jpg
    12.2 KB · Views: 4
You must log in or register to reply here.

Similar threads

tstick
What does a water pipe actually filter out of the smoke?
2
Replies
20
Views
1K
Jjgrow420
Jjgrow420
tstick
Smoking filtration vs Straight smoke
Replies
2
Views
263
tstick
tstick
W
what is best vape,pipe,bong,joint?
Replies
14
Views
1K
lokie
lokie
warble
  • Poll Poll
Hold your smoke or exhale, as soon as you finish hitting it? Survey.
2 3
Replies
41
Views
3K
lp10731
L
medidedicated
Looking for strains that cure well
2
Replies
27
Views
2K
medidedicated
medidedicated
Back
Top