123canadaguy
Member
So here's what I've been working on for the last couple months.
Project: Turn a broken 4.4cu ft mini fridge I got for free locally into a semi-automated, completely stealth grow box.
First Grow Journal: https://www.rollitup.org/t/first-grow-3-strains-184w-cfl-mini-fridge.954055/
Prep: First I gutted everything that made it a fridge. I had a friend purge the refrigerant for me so I could remove the compressor and lines safely. I removed the shelving on the inside and the separate section for the freezer. I took off the door and rubber seal, using a Dremel to cut out the plastic that would have held cans and bottles on the inside. A couple screws later and the temperature controls were removed, leaving me the perfect wires for lighting already ran to the inside. I plan to cut out the step at the bottom later so there is more floor space inside.
Reflectivity: To line the inside of the fridge I used about half of a 25 sqft roll of Reflectix insulation from Lowes and aluminum HVAC tape. I measured the dimensions, cut and taped it to the inside. The ceiling of the box doesn't matter. Before reattaching the door I also insulated it. The plastic cutout when screwed back on over top made a tight seal with the insulation.
Exhaust: At the top I cut a 4 inch hole which I tapered on the inside to fit a 120mm 12v exhaust fan rated at 121cfm. I used silicone around the edge of it to make it airtight and 2 threaded rods through the back of the fridge to hold it in place. Using my 3D modeling experience I designed and 3D printed a custom 4 inch elbow to fit a Can Filter 1500 flange which was also printed. It was siliconed over the 4 inch hole to attach the filter vertically on the outside. This keeps it out of sight when the fridge is against a wall and it sits as close to the fridge as possible to save space.
Intake: One 2" hole was drilled on each side of the fridge at the bottom. Fabric from some General Hydroponics bandannas are covering the holes as a temporary filter. When the door closes you can see they get sucked in from the pressure so no worry about smell. Eventually I'll be 3D printing a light trap for each hole and air filter mounts.
Electrical: I used the existing fridge wiring at the back and added a 24 hour timer in line with the wiring that runs to the inside of the fridge. This controls 184 watts of CFL bulbs (4x 23w 5000k & 4x 23w 2700k). Branching off the existing wiring I also added a 12v step down for the exhaust fan. The fan is currently controlled by a DC motor controller at a constant speed. Im looking into having the fans controlled by temperature/humidity or an Arduino instead of having just one set speed. Wiring works for now I'll tidy it up eventually.
It's still a work in progress and has turned into more of a hobby than anything. Let me know what you think!
![20171126_234658.jpg](/data/attachments/3149/3149472-0ae2fa2447fe2ea519c09a74fae22a6c.jpg)
Project: Turn a broken 4.4cu ft mini fridge I got for free locally into a semi-automated, completely stealth grow box.
First Grow Journal: https://www.rollitup.org/t/first-grow-3-strains-184w-cfl-mini-fridge.954055/
Prep: First I gutted everything that made it a fridge. I had a friend purge the refrigerant for me so I could remove the compressor and lines safely. I removed the shelving on the inside and the separate section for the freezer. I took off the door and rubber seal, using a Dremel to cut out the plastic that would have held cans and bottles on the inside. A couple screws later and the temperature controls were removed, leaving me the perfect wires for lighting already ran to the inside. I plan to cut out the step at the bottom later so there is more floor space inside.
Reflectivity: To line the inside of the fridge I used about half of a 25 sqft roll of Reflectix insulation from Lowes and aluminum HVAC tape. I measured the dimensions, cut and taped it to the inside. The ceiling of the box doesn't matter. Before reattaching the door I also insulated it. The plastic cutout when screwed back on over top made a tight seal with the insulation.
Exhaust: At the top I cut a 4 inch hole which I tapered on the inside to fit a 120mm 12v exhaust fan rated at 121cfm. I used silicone around the edge of it to make it airtight and 2 threaded rods through the back of the fridge to hold it in place. Using my 3D modeling experience I designed and 3D printed a custom 4 inch elbow to fit a Can Filter 1500 flange which was also printed. It was siliconed over the 4 inch hole to attach the filter vertically on the outside. This keeps it out of sight when the fridge is against a wall and it sits as close to the fridge as possible to save space.
Intake: One 2" hole was drilled on each side of the fridge at the bottom. Fabric from some General Hydroponics bandannas are covering the holes as a temporary filter. When the door closes you can see they get sucked in from the pressure so no worry about smell. Eventually I'll be 3D printing a light trap for each hole and air filter mounts.
Electrical: I used the existing fridge wiring at the back and added a 24 hour timer in line with the wiring that runs to the inside of the fridge. This controls 184 watts of CFL bulbs (4x 23w 5000k & 4x 23w 2700k). Branching off the existing wiring I also added a 12v step down for the exhaust fan. The fan is currently controlled by a DC motor controller at a constant speed. Im looking into having the fans controlled by temperature/humidity or an Arduino instead of having just one set speed. Wiring works for now I'll tidy it up eventually.
It's still a work in progress and has turned into more of a hobby than anything. Let me know what you think!
![20171126_234515.jpg](/data/attachments/3149/3149461-47b91ebc376cff4943af625b23bd3f9b.jpg)
![20171127_001047.jpg](/data/attachments/3149/3149463-2873a86225b94fa9e49a38e59da580f0.jpg)
![20171126_234523.jpg](/data/attachments/3149/3149464-975ebc575ccf7ab59f98704da363c08c.jpg)
![20171126_234529.jpg](/data/attachments/3149/3149465-5cee45c0aa4213a56098281eb5f52f86.jpg)
![20171126_234549.jpg](/data/attachments/3149/3149468-3254bd8cdd7cb07fbc9ed6dc9a269632.jpg)
![20171126_234603.jpg](/data/attachments/3149/3149469-0c717dd75f0837ad48eeef0360c3d548.jpg)
![20171126_234610.jpg](/data/attachments/3149/3149470-87834225cb9cd7296a3e0d5532c30a04.jpg)
![20171126_234621.jpg](/data/attachments/3149/3149471-0282e5b84308fdc201d61716065ae602.jpg)
![20171126_234658.jpg](/data/attachments/3149/3149472-0ae2fa2447fe2ea519c09a74fae22a6c.jpg)
Attachments
-
2 MB Views: 1
Last edited: