DIY with Quantum Boards

legalcanada

legalcanada

Well-Known Member
so am i understanding this correctly, hlg-240h-1050 will only be able to run them at 65% of the 1.6A max? would i require hlg-480-2100 to run 2x qb304 at max current or is there another option?
 
Last edited:
JustMeds

JustMeds

Well-Known Member
I got 4 boards and the hlg 480-2100 driver last go around. Can I add 2 more 5000k boards off that driver for 6 boards in total? The first 4 are all 3000k thinking of adding to the spectrum.
 
Budzbuddha

Budzbuddha

Well-Known Member
Amnesia Haze Auto getting the axe tomorrow... This auto was really not what I expected.
I am rather new to Royal Queen seeds and really am kinda pissed. I found out that THIS amnesia " VERSION " is a cross with LOWRYDER !
I hate LOWRYDER / Dwarfy strains .... But she smells awesome but really didn't get all that big. Chunky but guess this will be used for RSO or glycerin.
Fucking freebies ! .... Hahaha

image.jpeg
 
robincnn

robincnn

Well-Known Member
Blake_n_Concentrates said:
Question for you LED experts out there... is there any LED controllers that I can use to control 2 boards that will dim them based solely off of room temperature? Most of the dimmers I have seen can simulate light cycles and even clouds and shit, but I don't see any mention of being able to set a temp. probe to 78F and have the lights dim to whatever % to keep the room there. Or even turn off completely if need be... Any ideas?
Click to expand...
i have thermal switches. They usually trip at higher temps.
the one i have is 55C.. not sure how lower temps thermal switches go. temps need to go down 3C-6C below trigger point to un-trip

Thermistor may work alone or with a resistor in series. check datasheet and resistance vs temp charts . may work on type b driver.
upload_2017-6-14_22-10-5.png

Arduino could be a better way. you will run into that voltage issue .i think outputs are like 3.3 or 5v and does not match the 1-10V that meanwell driver dimming needs.
 
robincnn

robincnn

Well-Known Member
legalcanada said:
I just ordered my 4x qb304 and a slate 5! Excited! but still slightly confused about matching drivers. Is there a single driver that can power 4x qb304 at 90%-100% or would I need 2 drivers? Thanks
Click to expand...
Go with 2 drivers. HLG-240H-C1050A or HLG-240H-C1050B
I will add a 2 cable joiner so you have 1 power cord. Pm order #
Like Steve said 320H needed for 2 boards to max out.

legalcanada said:
so am i understanding this correctly, hlg-240h-1050 will only be able to run them at 65% of the 1.6A max? would i require hlg-480-2100 to run 2x qb304 at max current or is there another option?
Click to expand...
does not sound right
hlg-240h-1050A will give you 1.22 Amps not 1.6A. so 2 boards on this driver will give max 260-300 watts
hlg-480-2100 with 2x Qb 304 is not good. too much power.
hlg-320-1400 with 2x Qb 304 is nmax you want to try. dim it down if for some reason power draw exceeds 375 watts
 
A

AJdosMIL

Member
Hi All,

I Picked up 2x qb304 4000 and 2x qb304 3000 with a slate 5.ORDER HLG#1282

Is hlg-320-1400 dialed down using 100 potentiometer the correct route to go?

Happy New Light day to all that have placed/placing order this run! This one is going to fit in nice when starts heating up this summer.
 
robincnn

robincnn

Well-Known Member
eminiplayer said:
I'd be interested in these. Any chance of stocking them on your site?

Do they look like this... ??

View attachment 3961241
Click to expand...
only included in kits. I can consider adding this part in catalog if it helps.

https://www.newegg.com/Product/Product.aspx?Item=9SIA27C3TF9483&ignorebbr=1&nm_mc=KNC-GoogleMKP-PC&cm_mmc=KNC-GoogleMKP-PC-_-pla-_-HI+-+Electrical+&+Industrial+Wire-_-9SIA27C3TF9483&gclid=CjwKEAjwvYPKBRCYr5GLgNCJ_jsSJABqwfw71rCJfsnmxNgiylAd2H33-rIdVn34sSFFveAnJMl-qxoCIdXw_wcB&gclsrc=aw.ds

https://www.ebay.com/p/L20-T-shape-Ip67-Waterproof-Connector-3-Pin-Cable-Wire-Plug-Socket-Joint-Hs382/1380603669?iid=371899355316
 
ganglyguy420

ganglyguy420

Well-Known Member
robincnn said:
slate 5 is the only heatsink that can handle this much power...
View attachment 3961266
Click to expand...
i think im gonna buy this just cause i may want to run the qb's at more than 125 watts, but only plan on 100 per board. the heatsink shape is not really optimal for my flower room though i need rows of 3. will you guys come out with a wider single board heatsink that can handle more power to a single board? just so i can space them good. & is it best 3000k or 3500k for strait flower? from the charts they look so close i cant even really guess. last thing is im just wondering why the drivers are left on top of the heat sink, that doesnt obstruct it? its probably a stupid question but its just when im at work i wouldnt leave a control board on top of a tank even if there were no walls around to mount it to.
 
S

Stickyyickie

Member
Hello peeps, I need some advice.
Im about to order 2 of the 260w kit 3500k for my 4x4 tent. Do you think 3 would be better or is it overkill? I would like to maximize yield for my 4x4 tent. And I think Im gonna get a 260w kit 4000k for a veg light. Is 4000k good enough or is 5000k better for veg? Thanks!
 
ttystikk

ttystikk

Well-Known Member
Stickyyickie said:
Hello peeps, I need some advice.
Im about to order 2 of the 260w kit 3500k for my 4x4 tent. Do you think 3 would be better or is it overkill? I would like to maximize yield for my 4x4 tent. And I think Im gonna get a 260w kit 4000k for a veg light. Is 4000k good enough or is 5000k better for veg? Thanks!
Click to expand...
2 of those 260W kits will do well in a 4x4 tent.

I veg just fine with 3500K. This allows for more options when expanding or whatever as well. Limiting the change in spectrum has also been said to reduce crazy stretch.
 
You must log in or register to reply here.
Top