Wonders Medical Grow: Round 2
- Thread starter wonderblunder
- Start date
wonderblunder
Well-Known Member
[QUOTE="SICC";3472589]is this a discussion board or a grow?? 
[/QUOTE]
It is a grow.......
I will have a diagram posted of the light positioning idea. I am just looking for input, and this grow really hasn't popped off. The plants are getting nice and big, and I am very happy with their growth..... They have doubled in size since going under the MH, but for now this grow is gonna be slow. I am hoping the switch will get flipped by the 18th of Decemeber, but I certainly want to give these girls the chance to get big.........
Fed with water yesterday, a little snowstorm ultra, and sweet grape. Tommorrow they get fed with full strength veg nutes.
Thank you for all your input, more pics and diagrams up today.......
[/QUOTE]It is a grow.......
I will have a diagram posted of the light positioning idea. I am just looking for input, and this grow really hasn't popped off. The plants are getting nice and big, and I am very happy with their growth..... They have doubled in size since going under the MH, but for now this grow is gonna be slow. I am hoping the switch will get flipped by the 18th of Decemeber, but I certainly want to give these girls the chance to get big.........
Fed with water yesterday, a little snowstorm ultra, and sweet grape. Tommorrow they get fed with full strength veg nutes.
Thank you for all your input, more pics and diagrams up today.......
wonderblunder
Well-Known Member
Having a problem uploading. Will be back to try again soon..... Keep in mind the Xtra Sun with the 400w MH will be placed vertically, but in a way where the bulb remains horizontal... Flourescent lighting will be hung so it is adjustable, and the 48" side is horizontal, and the 24" side is vertical.
theloadeddragon
Well-Known Member
your original diagram looked good...... and would work really well were you to have 400W 2 MH and 2 HPS, rather than just two MH....... even better if you could get a mover to go in a circular motion around the grow...... does that make sense?
theloadeddragon
Well-Known Member
here hope these might help you get an idea what I mean... Notice the light movers path is outside of where the plant pots are spaced approximately 16-18 inches laterally from plant pot center, that the 400W are angled for light direction facing into the circle at a perfect 45 degree angle for penetration and more direct lumens on PAR...... the plant in the center is Topped/Fimmed and supercropped out to the side rather than growing completely vertically blocking all the light from reaching the outer ring (in other words the center plant needs to be approximately 40% of the height of the outer ring, proportionally, throughout the entire grow, making the outer plants 2 1/2 ft tall, 18-24 inches in diameter, going into flower, while the center plant would be 1 ft tall, 24-30 inches in diameter, going into flower... in order to accomplish this and get the desired effect, you would want to SCROG the center plant using netting, to hold its main side branches down
And this is all assuming the room allows for 8x8x8
And this is all assuming the room allows for 8x8x8
Attachments
theloadeddragon
Well-Known Member
it would be more proprtional growing??? lol
"SICC"
Well-Known Member
lol i was only jokin with ya, but i was mostly talkin to the other peeps, will be lookin forward to the next update, this thread had ALOT of good info
theloadeddragon
Well-Known Member
shit even if you don't do it, I will.... as soon as I have a couple more 400W HID built in units, and an extra 1000W set up.......... (next summer 
)
)
OregonMeds
Well-Known Member
The plant in the center Might interfere with cooling once they thicken up, other than that the plan is good.
The center is where a fan should be pointing up at the bulb, fairly strong fan too. But if you can fit it and a fan and not block too much airflow ok then. You'll want an oscillating fan or two in there somewhere also.
The center is where a fan should be pointing up at the bulb, fairly strong fan too. But if you can fit it and a fan and not block too much airflow ok then. You'll want an oscillating fan or two in there somewhere also.
wonderblunder
Well-Known Member
I like this setup and diagrams. I also like those round light movers. That would be lots of work, and money. I am trying to limit my budget, as I have a tendency to spend too much in this department..
Definitely a fan in the center blowing directly up. I have drawn another diagram which hopefully will answer a lot of questions. Still looking for input of course. Its just my idea of convenience and what I have.....
Definitely feelin ya, its amazing how cool a bare bulb can stay with fan blowing directly up........ I have been doing some experiments........
theloadeddragon
Well-Known Member
Fan would be in center ABOVE the HPS, sucking air through and exhausting (partially for air pressure reasons
), the schematic is based on a cool tube being used with the HPS to contain its heat, cool air intake should always come in low to the ground, and then be circulated by a fan, the Exhaust coming off the HPS will pull air from the cool air intake into the center of the room and up, and a couple oscillating fans just at and above canopy height will help pull air up through the plants and recirculate it around.The schematics I posted were done in like 5 minutes, just rough stuff so WB would get the idea of what I was saying...... I may have just gotten some space cleared up to get something like this going....... just to try it...... maybe in February or March?
wonderblunder
Well-Known Member
#1Raiderfan420
Well-Known Member
I would put the mh's on top, keep the verticle in the middle and rund 4 t-8's around the outsides unless you wanted to run the mh's around all 4 sides. Just my two cents.
Edit- sorry, you want this all verticle don't you? It looks good execpt you might have to keep those mh's a decent distance from the sides and the t-s can be right on em, so there may some light variance.
OregonMeds
Well-Known Member
Fan would be in center ABOVE the HPS, sucking air through and exhausting (partially for air pressure reasons
The schematics I posted were done in like 5 minutes, just rough stuff so WB would get the idea of what I was saying...... I may have just gotten some space cleared up to get something like this going....... just to try it...... maybe in February or March?
Oh cooltube, no problem then. Yea it's been hard for me to try clearing room too. My garage was full of shit stacked to the ceiling and I really want to grow in there so I've been working on it when I can. Now it's just a thin layer. I figure by the end of January it might finally be clear at the rate I'm going.
StOnEd SoLdIeR
Member
If your gonna do it like that would you need to rotate the circle so each plant would get the same time around the MH's? and turn the plants a quarter turn or so so they will get the same lighting around the HPS? It just seems like the plants will be getting so much light from one side and very little on others areas.
theloadeddragon
Well-Known Member
haven't you seen the plant spinner on GTO's thread? 2 complete 360's per hour
bender420
Well-Known Member
Wonderblunder, that is almost dead on to what i would do if I had the equipment or space. The only thing which would definitely be required is a platform that you could either rotate with a motor or manually on everyday or every other day basis.
Similar threads
