Thermoelectric wine cooler drying and curing - DIY

Mr. Mohaskey

Well-Known Member
Gonna chime back in here say, damn this is the easiest and best way to cure some bud. Straight cut off the vine right into the cooler. Drop down 1% per day. Been chilling at 55f and 3 wks later 58% humidity, and damn everything fine. Might be best thing I've added to much arsenal. I'd never go back. Thanks @Hook Daddy , you the man!
 
Would some kind soul give me a brief procedure on drilling the fridge including type and size of bit.

TYVM
I used a 3/8 bit. I'm used a ac infinity controller, so the wires for the dehumidifier and the controller fit nice. Then I got a 3/8 rubber grommet. I use a small dap of silicone on the inside.
 

Attachments

Be careful that you don’t drill a hole into gas insulated walls as I have it. Instead I use thin wires and use the hole for the water drip IMG_5853.jpegIMG_5856.jpeg
 

gooshpoo

Well-Known Member
@gooshpoo, on the 78L/bigger unit I got, the drain is elevated. Is yours as well, and if so how are you draining the dehu?
I just have mine sitting at a angle everything is draining fine for me but check the thermal electric heat-sink in the back, make sure everything is tight mine leaked a tiny bit.
I also used these for my hole inside and out.
Hole grommet
 

NutterDeep

New Member
Would it hurt to add a small computer fan in the bottom running all the time to circulate air like the cannatrol ? I no the dehu has a fan but it only runs when it kicks on, I don’t think a fan blowing up would be that great of idea but what about a fan fastened to bottom of bottom tray blowing down to circulate air ?
 

NutterDeep

New Member
Also I added my own drain for dehu in the center where I put the white dot at in pic,I drilled a 1/2 hole through bottom and put a piece of rubber tubing in hole and use a thin cookie sheet under the unit,works great ! I get no standing water in the bottom anymore like I was with the factory drain !
 

Attachments

Hook Daddy

Well-Known Member
Would it hurt to add a small computer fan in the bottom running all the time to circulate air like the cannatrol ? I no the dehu has a fan but it only runs when it kicks on, I don’t think a fan blowing up would be that great of idea but what about a fan fastened to bottom of bottom tray blowing down to circulate air ?
I don’t think it would hurt, but don’t think it’s necessary either. I don’t know of anyone that has added an extra fan, nor anyone that has had an issue an extra fan would solve.
 

xYEETMANx

Member
Also I added my own drain for dehu in the center where I put the white dot at in pic,I drilled a 1/2 hole through bottom and put a piece of rubber tubing in hole and use a thin cookie sheet under the unit,works great ! I get no standing water in the bottom anymore like I was with the factory drain !
Interesting lol I was trying to cut out a tray tilted to the hole in the back. Did you notice any temp difference?
 

sgnpuflm

Active Member
I've got everything I need ready, except I'm waiting on the 78L cooler to be delivered. Using the AC Infinity Controller 79P, I don't think I'll need to drill a big hole for that sensor or the wires, so hoping it goes easily.

I'm building it because I need one, but also, I'll be drying soon and need to leave town towards the end of a dry. One of the things I was anticipating needing to do was draining or toweling up the water, but it seems people are draining it either with a drain hole in the unit already (?) or an added hole under the peltier. @gooshpoo Can you provide a picture of the way your peltier sits in the 78L cooler? I think that's the only thing I'm still a little unsure of.

I should be mostly done drying when I need to leave, but I was worried about there still being water that needs to be collected by the time I leave. If I can just set up a drain and a cookie sheet to collect it, it'd solve my problem. Also, I'm assuming no problem with having to potentially leave during the dry? I went with the 79P so I could control it from a distance with the WiFi controller, where I'll be able to monitor/adjust as needed.
 

gooshpoo

Well-Known Member
I've got everything I need ready, except I'm waiting on the 78L cooler to be delivered. Using the AC Infinity Controller 79P, I don't think I'll need to drill a big hole for that sensor or the wires, so hoping it goes easily.

I'm building it because I need one, but also, I'll be drying soon and need to leave town towards the end of a dry. One of the things I was anticipating needing to do was draining or toweling up the water, but it seems people are draining it either with a drain hole in the unit already (?) or an added hole under the peltier. @gooshpoo Can you provide a picture of the way your peltier sits in the 78L cooler? I think that's the only thing I'm still a little unsure of.

I should be mostly done drying when I need to leave, but I was worried about there still being water that needs to be collected by the time I leave. If I can just set up a drain and a cookie sheet to collect it, it'd solve my problem. Also, I'm assuming no problem with having to potentially leave during the dry? I went with the 79P so I could control it from a distance with the WiFi controller, where I'll be able to monitor/adjust as needed.
Ill try and get you a photo, but its just sat in the bottom with the cold side down in the center back of the unit.
 
Top