Flower tent LED build

Airwalker16

Airwalker16

Well-Known Member
Powertech said:
They definitely look different
Click to expand...
So Yo, Power Tech, these are 84V I you said. is that each diode, each set of 6 of the 2 types, or is that for the entire board all 12 LEDs?
You said XLG-100-L-AB for both strips or just 1?
I'm mainly trying to find out the MA you run these at
 
Powertech

Powertech

Well-Known Member
Airwalker16 said:
So Yo, Power Tech, these are 84V I you said. is that each diode, each set of 6 of the 2 types, or is that for the entire board all 12 LEDs?
You said XLG-100-L-AB for both strips or just 1?
I'm mainly trying to find out the MA you run these at
Click to expand...
700mA, that's from the manufacture. Yes I know I will have them underpowered a bit, but can't find a driver with 117.6 Watts
 
Powertech

Powertech

Well-Known Member
Yeah, but I figured i'm not actually affiliated with Weed for Warriors, so I probably shouldn't use their logo

Sounds like it could be a good organization, but they obviously need some better actual organizing. No returns of emails from listings on websites
 
fragileassassin

fragileassassin

Well-Known Member
Powertech said:
Yeah, but I figured i'm not actually affiliated with Weed for Warriors, so I probably shouldn't use their logo

Sounds like it could be a good organization, but they obviously need some better actual organizing. No returns of emails from listings on websites
Click to expand...
I want to get with some kind of program like that but i cant find one in CO.
 
Powertech

Powertech

Well-Known Member
I tried multiple times to get in contact with somebody, but to no avail. This was before I started growing and actually needed some help. Now that I am growing I don't need the help, and I help a few myself
 
Gond00s

Gond00s

Well-Known Member
hows the room looking, just pulled the trigger for 18 strips gonna do 3 14mm strips per heatsink, for your cutter strips how hard do u run them?
 
Powertech

Powertech

Well-Known Member
Gond00s said:
hows the room looking, just pulled the trigger for 18 strips gonna do 3 14mm strips per heatsink, for your cutter strips how hard do u run them?
Click to expand...
My room is at a stand still until the last 2 UVB strips come in. The beer virus screwed up shipping so they didn't even get the chips as of a couple days ago.

I have a lot of drivers, running the lights all different lol. The 3000k whites total have a max of 300W between 6 strips, I have them on a 240W driver, with massive heat sinks, 3 strips per heat sink, couple extra inches on each end for mounting and such, so i'd say I am not running them hard at all, actually only ran them for 6 hours so far just to check heat and stuff, not running them till I switch to flower, I have way too much light in here for veg

3.500" Wide Extruded Aluminum Heatsink | HeatsinkUSA

Visit HeatsinkUSA where you'll find 3.500" wide extruded aluminum heatsinks available for you to order today. Shop our wide selection of heatsinks today.
www.heatsinkusa.com www.heatsinkusa.com
 
fragileassassin

fragileassassin

Well-Known Member
Powertech said:
If I get some kind of affiliation, i'll change the logo back. I also don't want to be affiliated with an organization that doesn't actually help
Click to expand...
Im kinda in a similar situation here. Multiple military installations around and LOTS of military come here to retire.
I found a few old sites and FB pages, but I cant find anything thats active.
Maybe ill just go gift quarters to people out in front of the VA clinic LOL though that is federal property so that might not be the best idea...
 
You must log in or register to reply here.
Top